通過將速度和所有相應狀態變量設置為零,這個選項被用來給一個結構退火。產品(Products):Abaqus/Explicit　Abaqus/CAE類型(Type):歷史數據等級(Level):分析步Abaqus/CAE:分析步模塊(Stepmodule)參考(Reference):·“Annealingprocedure,”Section6.12.1oft...[繼續閱讀]

    這個選項用來定義彈-塑性材料的退火溫度。它必須與*PLASTIC選項一起使用。產品(Products):Abaqus/StandardAbaqus/ExplicitAbaqus/CAE類型(Type):模型數據等級(Level):模型Abaqus/CAE:屬性模塊(Propertymodule)參考(Reference):·“Annealingormelting,”Sect...[繼續閱讀]

    這個選項用來定義流體屬性和穩態流體的速度。產品(Products):Abaqus/Aqua類型(Type):模型數據等級(Level):模型參考(Reference):·“Abaqus/Aquaanalysis,”Section6.11.1oftheAbaqusAnalysisUsersGuide可選的參數:INPUT(輸入)設定這個參數,等于(包含該選項所需數...[繼續閱讀]

    這個選項用來開始一個裝配定義,必須與*ENDASSEMBLY、*INSTANCE和*PART選項一起使用。產品(Products):Abaqus/StandardAbaqus/ExplicitAbaqus/CFDAbaqus/CAE　類型(Type):模型數據等級(Level):模型Abaqus/CAE:裝配模塊(Assemblymodule)參考(Reference):·*ENDASS...[繼續閱讀]

    這個選項用來允許Abaqus/Standard為(與CAXAn或SAXAn單元一起使用的)類ISL和IRS的接觸單元,計算合適的積分面積。*ASYMMETRIC-AXISYMMETRIC選項必須與*INTERFACE選項一起使用。產品(Products):Abaqus/Standard類型(Type):模型數據等級(Level):部件,部件實例...[繼續閱讀]

    這個選項僅能與*BEAMGENERALSECTION,SECTION=NONLINEARGENERAL選項一起使用。產品(Products):Abaqus/Standard　Abaqus/Explicit類型(Type):模型數據等級(Level):部件,部件實例參考(Reference):·*BEAMGENERALSECTION·“Usingageneralbeamsectiontodefinethesectionbehavior,”Sec...[繼續閱讀]

    這個選項僅在(使用系統固有模態的)線性動力學程序(*STEADYSTATEDYNAMICS無DIRECT參數、*MODALDYNAMIC和*RANDOMRESPONSE)中有效。產品(Products):Abaqus/Standard類型(Type):歷史數據等級(Level):分析步參考(Reference):·“Naturalfrequencyextraction,”Section6.3.5of...[繼續閱讀]

    這個選項用于修改加速度歷史,以減小(從給定加速度的時間積分中獲得的)位移的總體漂移(overalldrift)。它必須立即出現在*AMPLITUDE選項的數據行之后。產品(Products):Abaqus/StandardAbaqus/CAE　類型(Type):模型或歷史數據等級(Level):模型,分析...[繼續閱讀]

    這個選項與*BEAMSECTION或*BEAMGENERALSECTION選項一起,以定義(剪切柔性Timoshenko梁?jiǎn)卧?單位長度上的額外質量和轉動慣量。這個選項也可用來定義質量比例阻尼(用于直接積分動力學分析)和(與附加慣性有關的)復合阻尼(用于Abaqus/Stand...[繼續閱讀]

    這個選項與*BEAMSECTION或*BEAMGENERALSECTION選項一起使用,以包括(由于浸入無黏流體引起的)Timoshenko梁?jiǎn)卧械母郊討T性效應。產品(Products):Abaqus/StandardAbaqus/ExplicitAbaqus/CAE類型(Type):模型數據等級(Level):部件,部件實例,裝配Abaqus/CA...[繼續閱讀]